前言
關于Linux系統的HugePages與Oracle數據庫優化,可以參考熊爺之前的文章,相關概念介紹的非常清晰:
Linux大內存頁Oracle數據庫優化
本文旨在Linux系統上快速配置HugePages
測試環境:RHEL6.8 + 512G物理內存;Oracle 11.2.0.4 SGA=400G.
1.設置memlock無限制
在/etc/security/limits.conf配置文件中,設置oracle用戶memlock無限制:
vi /etc/security/limits.conf
oracle soft memlock unlimited
oracle hard memlock unlimited
2.設置合理的vm.nr_hugepages
在/etc/sysctl.conf配置文件中,設置合理的vm.nr_hugepages值。
運行MOS 401749.1提供的hugepages_settings.sh腳本,直接可以得到建議值。
hugepages_settings.sh腳本內容:
#!/bin/bash
#
# hugepages_settings.sh
#
# Linux bash script to compute values for the
# recommended HugePages/HugeTLB configuration
# on Oracle Linux
#
# Note: This script does calculation for all shared memory
# segments available when the script is run, no matter it
# is an Oracle RDBMS shared memory segment or not.
#
# This script is provided by Doc ID 401749.1 from My Oracle Support
# http://support.oracle.com
# Welcome text
echo "
This script is provided by Doc ID 401749.1 from My Oracle Support
(http://support.oracle.com) where it is intended to compute values for
the recommended HugePages/HugeTLB configuration for the current shared
memory segments on Oracle Linux. Before proceeding with the execution please note following:
* For ASM instance, it needs to configure ASMM instead of AMM.
* The 'pga_aggregate_target' is outside the SGA and
you should accommodate this while calculating SGA size.
* In case you changes the DB SGA size,
as the new SGA will not fit in the previous HugePages configuration,
it had better disable the whole HugePages,
start the DB with new SGA size and run the script again.
And make sure that:
* Oracle Database instance(s) are up and running
* Oracle Database 11g Automatic Memory Management (AMM) is not setup
(See Doc ID 749851.1)
* The shared memory segments can be listed by command:
# ipcs -m
Press Enter to proceed..."
read
# Check for the kernel version
KERN=`uname -r | awk -F. '{ printf("%d.%d\n",$1,$2); }'`
# Find out the HugePage size
HPG_SZ=`grep Hugepagesize /proc/meminfo | awk '{print $2}'`
if [ -z "$HPG_SZ" ];then
echo "The hugepages may not be supported in the system where the script is being executed."
exit 1
fi
# Initialize the counter
NUM_PG=0
# Cumulative number of pages required to handle the running shared memory segments
for SEG_BYTES in `ipcs -m | cut -c44-300 | awk '{print $1}' | grep "[0-9][0-9]*"`
do
MIN_PG=`echo "$SEG_BYTES/($HPG_SZ*1024)" | bc -q`
if [ $MIN_PG -gt 0 ]; then
NUM_PG=`echo "$NUM_PG+$MIN_PG+1" | bc -q`
fi
done
RES_BYTES=`echo "$NUM_PG * $HPG_SZ * 1024" | bc -q`
# An SGA less than 100MB does not make sense
# Bail out if that is the case
if [ $RES_BYTES -lt 100000000 ]; then
echo "***********"
echo "** ERROR **"
echo "***********"
echo "Sorry! There are not enough total of shared memory segments allocated for
HugePages configuration. HugePages can only be used for shared memory segments
that you can list by command:
# ipcs -m
of a size that can match an Oracle Database SGA. Please make sure that:
* Oracle Database instance is up and running
* Oracle Database 11g Automatic Memory Management (AMM) is not configured"
exit 1
fi
# Finish with results
case $KERN in
'2.2') echo "Kernel version $KERN is not supported. Exiting." ;;
'2.4') HUGETLB_POOL=`echo "$NUM_PG*$HPG_SZ/1024" | bc -q`;
echo "Recommended setting: vm.hugetlb_pool = $HUGETLB_POOL" ;;
'2.6') echo "Recommended setting: vm.nr_hugepages = $NUM_PG" ;;
'3.8') echo "Recommended setting: vm.nr_hugepages = $NUM_PG" ;;
'3.10') echo "Recommended setting: vm.nr_hugepages = $NUM_PG" ;;
'4.1') echo "Recommended setting: vm.nr_hugepages = $NUM_PG" ;;
esac
# End
直接運行腳本即可得到對應的建議:
--當啟動的實例設置SGA_MAX_SIZE=12G,給出建議:
Recommended setting: vm.nr_hugepages = 6148
--當啟動的實例設置SGA_MAX_SIZE=400G,給出建議:
Recommended setting: vm.nr_hugepages = 204805
--當沒有啟動實例時,會報錯提示:
***********
** ERROR **
***********
Sorry! There are not enough total of shared memory segments allocated for
HugePages configuration. HugePages can only be used for shared memory segments
that you can list by command:
# ipcs -m
of a size that can match an Oracle Database SGA. Please make sure that:
* Oracle Database instance is up and running
* Oracle Database 11g Automatic Memory Management (AMM) is not configured
我這里將建議值vm.nr_hugepages = 204805追加到/etc/sysctl.conf配置文件中,然后執行sysctl -p生效配置。
3.確認HugePages設置成功
查看關于HugePages的信息,注意HugePages_Total值是之前設置的204805:
grep Huge /proc/meminfo
# grep Huge /proc/meminfo
AnonHugePages: 0 kB
HugePages_Total: 204805
HugePages_Free: 168475
HugePages_Rsvd: 168471
HugePages_Surp: 0
Hugepagesize: 2048 kB
數據庫在啟動時,對應alert日志中會有“Large Pages Information”內容:
Wed Nov 14 14:38:12 2018
Starting ORACLE instance (normal)
************************ Large Pages Information *******************
Per process system memlock (soft) limit = UNLIMITED
Total Shared Global Region in Large Pages = 400 GB (100%)
Large Pages used by this instance: 204801 (400 GB)
Large Pages unused system wide = 4 (8192 KB)
Large Pages configured system wide = 204805 (400 GB)
Large Page size = 2048 KB
********************************************************************
至此可以確認HugePages設置成功。
總結
以上就是這篇文章的全部內容了,希望本文的內容對大家的學習或者工作具有一定的參考學習價值,如果有疑問大家可以留言交流,謝謝大家對腳本之家的支持。